+91 90336 30547 latascientific@gmail.com
ISO-aligned QC · Borosilicate 3.3 · Pan India supply network
Borosilicate glass 90 degree bend with a thermometer branch on the elbow
Pipe Section

Bend 90° with Thermometer Branch

Glass 90° bend with DN 25 instrument branch, DN 40 to DN 300

Glass 90° bend with a DN 25 branch for a thermometer or probe — DN 40 to DN 300, with L and L1 dimensions.

Request a quotation Full technical data and dimensions Download datasheet
At a glance
Product typeGlass 90° bend with thermometer branch
MaterialBorosilicate 3.3
Nominal bore rangeDN 40 to DN 300 with DN 25 branch
End connectionBeaded pipe ends with backing flanges and PTFE-envelope gaskets
Flange drillingSee the drilling table — BS 10 Table E, BS 10 Table F and ASA drilling available
Pressure ratingNot published on the component datasheet — confirm with us for your duty
Temperature ratingNot published on the component datasheet — confirm with us for your duty
Dimensional standardAs per the Lata Scientific component datasheet

Product overview

What it does, and where it fits.

Putting a temperature probe into a bend rather than a straight section saves a fitting and puts the sensor where the flow is well mixed. This bend carries a DN 25 branch on the elbow for exactly that.

The branch is DN 25 across the whole range from DN 40 to DN 300, so one probe size fits every line. Two dimensions are given: L for the run and L1 to the branch face.

Features

Built into every unit.

  • DN 25 instrument branch at every bore from DN 40 to DN 300
  • Combines a direction change and an instrument point in one fitting
  • Type A at DN 40–50, Type B from DN 80 upward
  • Separate L and L1 setting-out dimensions

Benefits

Why it earns its place in the line.

  • One fitting instead of a bend plus a tee — fewer joints
  • Probe sits where the flow is well mixed by the turn
  • Completely inert to almost all process media — no metal pick-up and no contamination of the batch
  • Full visibility of the process along the whole line
  • Smooth, non-wetting bore that resists fouling and cleans easily

Applications & industries

Where it is specified.

Typical applications

  • Temperature measurement on a glass process line
  • Probe and thermowell points at a direction change
  • Retrofitting instrumentation without adding a tee
  • Distillation, absorption and scrubbing pipework

Industries served

  • Chemical processing
  • Pharmaceutical
  • Fine chemicals & dyes
  • Food & beverage
  • Water & effluent treatment
  • Distillation & solvent recovery
  • Research & pilot plant

Technical data

Specification for Bend 90° with Thermometer Branch.

Figures below are for this product only — every item in the range carries its own dimension table.

Bend 90° with Thermometer Branch — technical specification
Product typeGlass 90° bend with thermometer branch
MaterialBorosilicate 3.3
Nominal bore rangeDN 40 to DN 300 with DN 25 branch
End connectionBeaded pipe ends with backing flanges and PTFE-envelope gaskets
Flange drillingSee the drilling table — BS 10 Table E, BS 10 Table F and ASA drilling available
Pressure ratingNot published on the component datasheet — confirm with us for your duty
Temperature ratingNot published on the component datasheet — confirm with us for your duty
Dimensional standardAs per the Lata Scientific component datasheet
Catalogue referenceLSPBT series, e.g. LSPBT4 = DN 100
Bend 90° with Thermometer Branch — dimensions
Cat. Ref.DNDN1LL1Type
LSPBT1.54025150225A
LSPBT25025150225A
LSPBT38025200275B
LSPBT410025250350B
LSPBT615025250375B
LSPBT922525375525B
LSPBT1230025450550B

All dimensions in mm, transcribed exactly from the component datasheet.

FAQ

Questions we are asked about this item.

Yes — the datasheet lists DN 25 for the branch at every bore from DN 40 to DN 300.

No, the branch is the connection. See the thermometer pocket for bend, which is the pocket that fits into it.

Enquiry

Tell us your line size — we'll confirm the spec.

Send the bore, the media, the temperature and pressure, and the flange standard you work to. Drawings and custom sizes welcome.

Enquire on WhatsAppChat to us on +91 90336 30547 Bend 90° with Thermometer Branch datasheet (PDF)Dimensions and catalogue references for this item Talk to a technical expertMaterial selection and duty review Send a drawingWe fabricate to your isometric or sketch Request a custom sizeNon-standard bores, lengths and drilling

Not sure which spec fits your process?

Send your requirement — media, temperature, pressure, dimensions — and we'll recommend the right product or fabricate it.

Talk to an engineer